Installation and Usage Guide

Waterless Aroma Diffuser User Manual

Quick Start Guide

Before starting, fit the glass bottle and add compatible oil between the MIN and MAX levels.

Model without Light

Turn the control knob clockwise to start misting and adjust the intensity. The diffuser mists for 5 minutes, pauses for 3 minutes and repeats this cycle for 3 hours before switching off automatically.

Model with Light

Turn the knob to start misting and adjust the intensity, using the cycle above. Press the knob to cycle through brightness Levels I, II and III; press a fourth time to switch the light off.

Power and Charging

Power adapter: 5 V DC, 2 A or higher.

  • Plug-in: keep connected.
  • Cordless: red = charging; green = full.

If your cordless (battery-powered) diffuser does not produce mist, charge it for at least 30 minutes before trying again - even if the light turns on. This is especially important before first use or after the diffuser has not been used for a long time.

Oils and Cleaning

Compatible Oils

Use only ready-to-use, oil-based essential oils of a suitable viscosity, clearly labelled for use in waterless cold-air diffusers. Do not add water or use water-soluble products.

Oil Level

Keep the oil level between the minimum and maximum levels shown on the glass bottle. This maintains misting performance and helps prevent damage to the diffuser base.

Quick Cleaning

  1. Switch off and disconnect. Empty any remaining essential oil, then fit the glass bottle onto the base.
  2. Add warm water to cover the internal glass tube. Keep electrical connections dry. Reconnect power if needed and run for about one minute.
  3. Switch off and disconnect. Remove the bottle, empty it immediately and let it dry completely.

Cleaning liquids are for cleaning only. Empty immediately after cleaning and let the bottle dry completely before adding essential oil.

Full Instructions

Step 1 - Install the Glass Bottle

Installation

Insert the bottom stem of the glass bottle into the black gasket on the diffuser base. Keep the bottle upright and seat it securely.

Before assembly, switch off the diffuser and disconnect the power cable. Handle the glass bottle gently.

Glass bottle and black gasket on the diffuser base.
Glass bottle and black gasket on the diffuser base.

Step 2 - Add Oil

Compatible Oils

Use only ready-to-use, oil-based essential oils of a suitable viscosity, clearly labelled for use in waterless cold-air diffusers. Do not add water or use water-soluble products.

Remove the glass cap. Use the dropper to add oil to the glass bottle, then replace the cap.

Check the oil level before starting.

Add compatible oil with the dropper.
Add compatible oil with the dropper.

Oil Level

Keep the oil level between the minimum and maximum levels shown on the glass bottle. This maintains misting performance and helps prevent damage to the diffuser base.

Do not fill above MAX. Add enough oil to reach MIN before operation.

Do not add water to the oil.

Keep the oil between the MIN and MAX marks.
Keep the oil between the MIN and MAX marks.

Step 3 - Connect Power or Charge the Battery

Power Adapter Requirements

Power adapter: 5 V DC, 2 A or higher.

Plug-in Model

No charging is required. Keep the supplied power cable connected during operation.

Cordless Model

A full charge takes approximately 4 hours and provides up to 10 hours of total operation per charge, depending on the output setting.

  • Red: charging
  • Green: full
Connect the supplied power cable to a suitable power adapter.
Connect the supplied power cable to a suitable power adapter.

Cordless Model - No Mist?

If your cordless (battery-powered) diffuser does not produce mist, charge it for at least 30 minutes before trying again - even if the light turns on. This is especially important before first use or after the diffuser has not been used for a long time.

Step 4 - Start and Adjust Misting

Misting Controls

Connect the plug-in model or charge the cordless model as described above before starting.

Turn the control knob clockwise to start misting. Turn the knob to adjust the mist intensity. Turn it fully counterclockwise to switch the diffuser off.

The diffuser mists for 5 minutes, pauses for 3 minutes and repeats this cycle for 3 hours before switching off automatically.

Turn to adjust misting.
Turn to adjust misting.

Step 5 - Adjust the Light

Models with a Light Bulb

For models fitted with the light bulb accessory only.

Align the light bulb with the light socket and screw it in securely.

Press the control knob to cycle through brightness Levels I, II and III. Press it a fourth time to turn the light off.

Fit the compatible light bulb in the light socket.
Fit the compatible light bulb in the light socket.

Models with a Crystal Light

For models fitted with the crystal accessory only.

Place the crystal on the round light base.

Press the control knob to cycle through brightness Levels I, II and III. Press it a fourth time to turn the light off.

Place the crystal on the round light base.
Place the crystal on the round light base.

Turn the knob for misting. Press the knob for light.

Care and Cleaning

Cleaning Frequency

Clean the glass bottle regularly and whenever you change oils. Residue may build up inside the glass tube and reduce misting performance.

Before Cleaning

Switch off the diffuser and disconnect the power cable before removing or refitting the bottle, adding liquid, or emptying it. For cordless models, disconnecting the charging cable does not switch off the diffuser.

Bottle Removal

Keep the base and electrical connections dry. Hold the base with one hand and gently twist and pull up the bottom of the glass bottle with the other hand to remove it.

Soaking the Detached Bottle

  1. Switch off, disconnect the power cable and remove the glass bottle.
  2. Add warm water or alcohol to the detached bottle until the internal glass tube is covered. Leave for about 30 minutes, then gently shake for about one minute.
  3. Pour out all soaking liquid and allow the bottle to dry completely.

Use alcohol in a well-ventilated area, away from flames, sparks and heat. Do not heat alcohol.

Short Cleaning Cycle

  1. Switch off and disconnect. Empty any remaining essential oil, then fit the glass bottle onto the base.
  2. Add warm water or alcohol to cover the internal glass tube. Keep electrical connections dry.
  3. Reconnect power if needed and run the diffuser for about one minute.
  4. Switch off and disconnect. Remove the bottle and immediately pour out all cleaning liquid.
  5. Allow the bottle to dry completely before refilling with oil.

Water is for cleaning only. Empty immediately after use.

Replacement Parts and Oils

Glass Bottle

If the glass bottle is damaged, purchase a replacement from our official website. Do not use a damaged glass bottle.

Light Bulb

This product supports 5 V light bulbs only. Do not use 220 V or 110 V bulbs. Compatible bulbs are available on our official website.

Compatible Oils

Use only ready-to-use, oil-based essential oils of a suitable viscosity, clearly labelled for use in waterless cold-air diffusers. Do not add water or use water-soluble products.

Incompatible essential oils or an unsuitable viscosity may clog the glass bottle and result in weak or no mist output.

Storage

Diffuser Storage

If you do not plan to use the diffuser for an extended period, keep it in its original box.

Oil Storage

Store essential oils away from light and heat to preserve their quality and scent.

Safety Instructions

General Precautions

To reduce the risk of fire, electric shock or injury, read all instructions before use and follow them as directed.

Safe Operation

Do not inhale directly from the glass bottle. Do not cover the diffuser while in use.

Do not insert foreign objects or fingers into the diffuser. Do not drink diffuser oil.

Ensure good air circulation. If the scent becomes too intense, ventilate the room. Adjust the mist intensity to suit the room size.

Surface Protection

Avoid contact between oils and sensitive surfaces, including painted wood, lacquered furniture and acrylic finishes. Oils may cause discoloration, peeling or damage.

Electrical Safety

Do not modify or force a plug that does not fit. Switch off before unplugging. Hold the plug, not the cord.

Skin / Eye Contact

Do not touch the glass bottle while the diffuser is on.

If diffuser oil contacts the skin, wash the affected area with soap and water. If irritation occurs, consult a physician immediately.

Avoid contact with eyes. In case of eye contact, rinse immediately and consult a physician.

Supervision

This diffuser is not intended for use by children or persons with reduced physical, sensory or mental capabilities, or a lack of experience and knowledge.

Keep the diffuser and oils out of reach of children and pets.

Warranty and Support

Warranty Service

Charabanc Aroma diffusers are covered by a one-year warranty from the date of purchase. If a malfunction occurs during normal use, please contact our customer service team.

[email protected]

For issues outside the warranty scope, paid repairs or replacement parts are available. See the warranty exclusions below.

Warranty Exclusions

Not Covered Under Warranty

  • Damage caused by the use of third-party essential oils.
  • Damage caused by non-original or incompatible replacement parts.
  • Damage caused by improper use, storage or maintenance.
  • Damage caused by disassembly, modification or repair by unauthorized personnel.
  • Products beyond the warranty period.
  • Products without a valid order record or proof of purchase.

Video Tutorials

Related Reading

Back to blog